Top 10 typical forklift crashes ， forklift procedure must focus on these issues ！.

Top 10 typical forklift crashes ， forklift procedure must focus on these issues ！.

Blog Article

Do not ignore the forklift at the office. If the operation is bad, there will be significant crashes in mins, and there are many mishaps involving forklifts.

Instance 1: The forklift freight blocked the chauffeur's sight, and the individual in front could not be discovered, resulting in a moving mishap.
Case 2: In order to keep the balance of the forklift when raising hefty items, the workers utilized their body weight as the counterweight, which virtually caused casualties.
Situation 3: The size of the forklift freight exceeds the allowable width of the route and holds on the roadside rack, which almost creates an mishap.
Situation 4: Forklift is speeding up and surrender throughout a turn.
Instance 5: The forklift motorist did not notice the pedestrian, and the pedestrian did not observe the forklift.
Case 6: The forklift lifts the personnel illegally, the forklift motorist does not wear the seat belt, the forklift lifter drops and the driver is crushed when the forklift rolls over.
Instance 7: The forklift chauffeur did not use a seat belt and fell from the lorry when it surrendered and was crushed.
Forklift operation need to pay attention to these matters ：.

Start.
1. Prior to starting, observe the surroundings, and after validating that there are no challenges that hinder the security of driving, beep the horn first and after that start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic pressure (air pressure) scale have to be safe prior to beginning.
3. When the forklift starts with a load, the chauffeur must initially verify that the lots is secure and reliable.
4. The begin needs to be sluggish and consistent.

Driving.
1. When driving, the elevation in between the bottom end of the fork and the ground need to be maintained 300mm-400mm, and the pole needs to be slanted backwards. .
2. Do not lift the fork too high when driving. When entering and leaving the work website or while driving, be careful that there will be no obstacles overhead. When the tons is traveling, the fork must not be increased expensive, which will affect the security of the forklift. .
3. After unloading, the fork must be reduced to the normal driving position prior to driving. .
4. When transforming, if there are pedestrians or lorries close by, the driving signal must be released first. High-speed sharp turns are restricted. High-speed doglegs will certainly trigger the car to shed side security and tip over. .
5. When the forklift is downhill, it is purely restricted to shut off the flame and slide, and it is restricted to brake instantly while driving with lots unless there are special conditions.
6. When the forklift is running, it needs to comply with the web traffic rules in the factory and need to maintain a particular security range from the vehicle in front. .
7. When the forklift is running, the lots should remain in the lowest placement that does not impede the driving, and the gantry needs to be effectively slanted back. The load will not be raised other than when stacking or filling. .
8. The elevation of the load have to not block the driver's sight. In special conditions, when the thing impacts the forward vision, drive at a low rate when reversing.
9. It is restricted to activate the ramp, nor to drive across the ramp. .
10. The safe driving speed of the forklift in the manufacturing facility area is 5 km/h, and it must drive safely at a reduced rate when entering the production workshop area. .
11. When the forklift is lifted, lifted or driven, it is prohibited for employees to base on the fork to hold things and play a stabilizing function. .
12. If issues are located, they will certainly be fixed and reported in a timely manner, and they will certainly never operate with illnesses or hide them.

packing and unloading.
1. When fork-loading products, the range in between the two forks must be changed as required to make the lots of both forks well balanced and not manipulated, and one side of the thing must be against the rack. .
2. It is restricted to work with a single fork or utilize a fork top or draw. In unique scenarios, safety and security indication need to be set up to advise surrounding pedestrians. .
3. In the process of filling and discharging things, the forklift needs to be braked with the brake. .
4. The rate of the vehicle need to be slow Stand-on Electric Pallet Stacker and constant. Beware not to roll the wheels on the dunnage, so as not to extend the rolled objects and injure people. .
5. When utilizing a fork to fork the goods, the fork should be as deep as possible under the lots, and it ought to be kept in mind that the fork tip must not touch other products or things. The load must be maintained with minimal back tilt of the gantry to make sure that the Stand-on Electric Pallet Stacker load does not move in reverse. The mast can be tilted onward slightly when the load is reduced to permit easy placement of the tons and removal of the forks. .
6. It is forbidden to fork products at broadband and ram hard objects with the fork head. .
7. When the forklift is working, it is restricted for individuals to stand around the fork, so as to prevent the collapse of the goods and hurt individuals. .
8. Straining is prohibited, and it is restricted to make use of forks to raise employees to engage in high-altitude operations to prevent high-altitude falling mishaps. .
9. It is not permitted to make use of the brake inertia to slide, place, round or roll objects. .
10. It is not allowed to use forks to pick, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you need to dump the goods or reduced the fork structure.
2. Draw the hand brake handle to dead or depress the parking brake switch.
3. The engine is turned off and the power is cut off. (Except for unique circumstances, such as the driver does not leave the vehicle's line of sight and does not exceed 1 min).
4. Get rid of the secret. .

Forklift Operation Precautions.
1. Prior to and after the forklift operation, the appearance should be checked, and gas, lubing oil and air conditioning water ought to be added.
2. Check the safety efficiency of beginning, running and braking.
3. Check whether the lights and horn signals are full and reliable.
4. Throughout the operation of the forklift, check whether the stress and temperature level are typical.
5. After the forklift is running, the external leak must likewise be checked and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You should check prior to leaving the car;.
2. When you run into somebody in front of you throughout driving, you must send a signal at a distance of 5 m;.
3. The driving rate in the factory does not exceed 5 km/h;.
4. When driving, the nadir of the cargo need to be 0.3 m ~ 0.4 m in the air;.
5. The turning need to not be as well sharp to prevent the propensity of "free switching";.
6. Running up and down the incline ought to be slow-moving and uniform, and no turning on the incline is allowed.
7. Do not drive throughout the gradient. When the slope is greater than 10%, the automobile should be driven in reverse when going downhill;.
8. When the forklift employees carry the goods and move on, if they encounter huge or heavy products and most likely to the chauffeur's view, they ought to take the turning around exercise
.
The "Eight Prohibitions" must be followed in the operation.
1. Solitary fork operation is not enabled.
2. It is not permitted to lift the goods for far away driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll items.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive side to side on slopes
.
Auto parking is not allowed under the list below conditions.
1. Curves, narrow roads, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the barrier need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844